SBS改性瀝青防水卷材
SBS modified asphalt waterproofing membrane
SBS產品施工介紹
性能特點:低溫柔性好,達到-25℃不裂紋;耐熱性能高,90℃不流淌。延伸性能好,使用壽命長,施工簡便,污染小等特點。產品適用于Ⅰ、Ⅱ級建筑的防水工程,尤其適用于低溫寒冷地區和結構變形頻繁的建筑防水工程。
規格分類:按物理指標分為:Ⅰ(-20℃)、Ⅱ(-25℃)型兩大類;
按胎基可分為:聚酯胎、玻纖胎兩大類;按覆面材料可分sbs防水卷材
為:PE膜(鍍鋁膜)、彩砂、頁巖片、細砂等四大類;幅寬:1000mm,幅長有10m、15m兩種規格;厚度:聚酯氈卷材3mm、4mm、5mm;玻纖氈卷材3mm、4mm;玻纖增強聚酯氈卷材5mm
適用范圍:廣泛應用于工業和民用建筑的屋面、地下室、衛生間等防水工程以及屋頂花園、道路、橋梁、隧道、停車場、游泳池等工程的防水防潮。變形較大的工程建議選用延伸性能優異的聚酯胎產品,其他建筑宜選用相對經濟的玻纖胎產品。
SBS product construction introduction
Performance characteristics: low temperature flexibility, no crack at -25 °C; high heat resistance, no flow at 90 °C. Good extension performance, long service life, simple construction and low pollution. The product is suitable for the waterproof engineering of I and II buildings, especially for low temperature and cold areas and building waterproofing projects with frequent structural deformation.
Specification classification: divided into two categories according to physical indicators: I (-20 ° C), II (-25 ° C);
According to the tire base, it can be divided into two categories: polyester tire and glass fiber tire. According to the cladding material, it can be divided into sbs waterproof membrane.
It is: PE film (aluminum film), colored sand, shale film, fine sand and other four categories; width: 1000mm, length is 10m, 15m two specifications; thickness: polyester felt coil 3mm, 4mm, 5mm; glass fiber felt coil 3mm, 4mm; glass fiber reinforced polyester felt coil 5mm
Scope of application: It is widely used in waterproofing projects such as roofing, basement, and toilets for industrial and civil buildings, as well as waterproofing and dampproofing for roof gardens, roads, bridges, tunnels, parking lots, swimming pools, etc. For projects with large deformation, it is recommended to use polyester tire products with excellent extension performance. For other buildings, relatively economical fiberglass tire products should be used.
施工方法:
施工前應清理基層缺陷,基層含水率不大于9%,涂刷專用底子油并充分干燥后再施工。具體工程施工以及細部構造應按照工程的防水設計、驗收標準和施工規范進行。鋪設卷材
1、基層要求干燥、平整、干凈、無塵土、無雜物、無油污、無苔斑,如有孔、洞、裂縫要用水泥砂漿填實,突出部分要鑿平。
2、要逆風涂刷基層處理劑。
3、在基層表面和卷材表面涂膠粘劑,并預留搭接邊以涂刷接縫膠。
4、鋪貼卷材,并進行排氣、壓實。
5、進行搭接縫的粘貼。
Construction method:
Before the construction, the defects of the base layer should be cleaned, the moisture content of the base layer should be no more than 9%, and the special base oil should be brushed and fully dried before construction. The specific construction and detailed construction shall be carried out in accordance with the waterproof design, acceptance criteria and construction specifications of the project. Laying coil
1. The base layer requires dryness, smoothness, cleanness, no dust, no debris, no oil, no moss spots. If there are holes, holes and cracks, it should be filled with cement mortar, and the protruding parts should be leveled.
2. Apply the base treatment agent against the wind.
3. Apply adhesive on the surface of the base layer and the surface of the coil, and reserve the lap joint to apply the joint glue.
4, paving the coil, and exhaust, compaction.
5. Paste the lap joint.
貯存運輸:
(1)避免日曬雨淋,干燥通風環境下貯存。儲存溫度不得低于相應規格產品柔度試驗溫度(-℃),不應高于50℃。立式存放,高度不超過兩層;
(2)運輸時必須立放,高度不超過兩層,要防止傾斜或橫壓,必要時加蓋苫布。
(3)正常貯存和運輸條件下,貯存期自生產之日起為一年。
(4)運輸及儲存過程應遠離火源。
Storage and transportation:
(1) Avoid sun and rain, store in a dry and ventilated environment. The storage temperature shall not be lower than the product compliance test temperature (-°C) of the corresponding specification, and shall not be higher than 50 °C. Vertical storage, no more than two floors in height;
(2) It must be placed upright when transported, and the height should not exceed two layers. To prevent tilting or horizontal pressure, cover the cloth if necessary.
(3) Under normal storage and transportation conditions, the storage period is one year from the date of production.
(4) Transportation and storage should be kept away from fire.
全國免費服務熱線:400-843-6198