最新資訊
固浪建材有限公司：教您那些地方必須嚴格做好防水
2024年01月25日
室內工程瓷磚粘貼的技巧-固浪瓷磚膠
2024年01月26日
教您正確使用瓷磚膠的方法、固浪瓷磚膠
2024年01月26日
掉磚空鼓的克星就選“固浪瓷磚粘結劑”
2024年01月26日
“固浪瓷磚背膠”操作流程
2024年01月26日
聯系我們
固浪防水
固浪 400-843-6198
固浪 400-843-6198
1919860518@qq.com
QQ:1919860518
廣州市白云區鐘落潭鎮金盆工業區
固浪聚合物高分子防水卷材
2024年05月27日
聚合物自粘防水材料
Polymer self-adhesive waterproof material
產品概述Product Overview：
自粘防水卷材是一種以SBS等合成橡膠、增粘劑及優質道路石油瀝青等配制成的自粘橡膠瀝青為基料，強韌的高密度聚乙烯膜或鋁箔作為上表面材料，可剝離的涂硅隔離膜或涂硅隔離紙為下表面防粘隔離材料制成的防水材料。它是一種極具發展前景的新型防水材料，具有低溫柔性、自愈性、及粘結性能好的特點，可常溫施工、施工速度快、符合環保要求。
Self-adhesive waterproofing membrane is a kind of self-adhesive rubber asphalt made of synthetic rubber such as SBS, tackifiers and high-quality road asphalt, etc. . The high-density polyethylene film or aluminum foil is used as the upper surface material, the peel-off silicon-coated isolation film or silicon-coated isolation paper is a waterproof material made of the anti-adhesion isolation material on the lower surface. It is a new waterproof material with great development prospect. It has the characteristics of low temperature flexibility, self-healing and good bonding property.
適用范圍Scope of application：
1, 適用于工業及民用建筑的屋面、地下室、室內、市政工程和蓄水池、游泳池以及地鐵隧道防水。
2，適用于木結構和金屬結構屋面的防水工程。
3，特別適用于不宜動用明火的石油庫、化工廠、紡織廠、糧庫等防水工程。
4，優異的低溫性能更適應寒冷地區適用。
1, suitable for industrial and civil building roofing, basement, indoor, municipal engineering and water storage pool, swimming pool and subway tunnel waterproof.
2, suitable for wood structure and metal structure roof waterproof engineering.
3, especially suitable for use of open fire oil depots, chemical plants, textile factories, grain depots and other waterproof works.
4, excellent low-temperature performance more suitable for cold areas.
施工工藝Construction Technology：
1、基層處理：清除基層表面的雜物，將突出基層表面的尖銳硬物、砂漿疙瘩等鏟除。 2、抹聚合物水泥砂漿：
2.1 配制聚合物水泥砂漿：水泥：中砂：聚合物：水=1:2:0.2:0.3，配制時，先將水泥、中砂干拌均勻攤開，并在中間形成凹坑，然后加入用水預配好的聚合物乳液或外加劑再次拌合，最后加入適量的水?dāng)嚢杈鶆蚣纯?。配制時防水砂漿的用水量應扣除聚合物乳液或外加劑及砂中的水量，將聚合物水泥砂漿充分?jǐn)嚢?直至呈粘稠狀。聚合物水泥砂漿拌合物應在1h內用完。在施工過程中如有離析現象，應進行二次拌和，必要時應加適量聚合物乳液，嚴禁任意加水。
2.2 抹聚合物水泥砂漿，其厚度一般為5mm～20mm（視基層平整情況而定），鋪抹時應注意壓實、抹平。在陰角處，應抹成半徑為50mm以上的圓角。鋪抹聚合物水泥砂漿的寬度比卷材的長、短邊宜各寬出100mm～300mm，并在鋪抹過程中確保一定的平整度。
3、細部附加層粘貼：在大面積鋪貼卷材前應先對三面角、水落口、地下穿墻管等易發生滲漏的薄弱環節加鋪一道卷材或涂膜，并在之前或之后用密封材料處理，形成多道設防的構造，附加防水層依據工程情況可先做亦可后做。
4、大面積鋪貼自粘防水層：
4.1平面：揭掉自粘防水卷材下表面的隔離膜將防水卷材平鋪在聚合物水泥砂漿上。采用搭接方式時，將下層卷材上表面搭接部位隔離膜及上層卷材下表面隔離膜揭除，然后搭接密實，搭接寬度不小于60mm。采用對接方式時，對上下表面使用封口材料（自粘卷材或涂膜）進行密封。
4.2立面：在基層上彈出卷材鋪貼控制線，鋪抹配制好的聚合物水泥砂漿（配制量必須在1h內用完）。從卷材的一端將隔離膜揭起，拉住揭下的隔離膜勻力向下拉，同時將揭掉隔離膜的部分粘貼在鋪抹好的聚合物水泥砂漿上。邊抹灰、邊鋪設卷材邊用抹子輕輕抹壓、拍打卷材表面，排氣、提漿，使卷材與水泥砂漿緊密粘合。鋪設卷材時，隨時注意與基準線對齊，速度不宜過快。
立面卷材與基層、卷材與卷材均采用滿粘法施工。
4.3卷材搭接和密封：相鄰卷材搭接縫及卷材收頭處應精心處理，可采用配套密封材料密閉或用自粘封口條進行蓋縫，隨后再用配套密封材料密閉。
4.4立面卷材收頭：立面卷材收頭，應先在卷材收口處臨時密封（可用封口材料或加厚水泥漿密封），以防止立面收頭處水分過快散失。亦可用配套密封材料密閉，或用自粘封口條進行蓋縫，隨后再用配套密封材料密閉加強處理。
5、防水層驗收：
檢查所有自粘卷材面有無撕裂、刺穿，維修時應在缺陷部位加補比缺陷部位實際尺寸四周寬100mm的附加層，用壓輥壓緊壓實，邊縫用專用密封材料做封邊處理。
6、保護層和隔離層施工：
卷材鋪貼完成并驗收合格后，應將施工廢料、垃圾等搬運到指定的垃圾場所，保持現場清潔，并將防水層表面清掃干凈，對防水層采取保護措施并根據設計要求進行防水保護層施工。
1, the grass-roots treatment: the removal of debris on the surface of the grass-roots, will highlight the surface of the sharp hard objects, such as the eradication of mortar pimple. 2. Smearing polymer cement mortar: 2.1 preparing polymer cement mortar: Cement: middle sand: polymer: water = 1:2:0.2:0.3, when preparing, first the cement, middle sand dry mix evenly spread out, and form a pit in the middle, then add water pre-prepared polymer emulsion or additives to mix again, and finally add the right amount of water to stir evenly. The amount of water used in the preparation of waterproof mortar should deduct the amount of water in polymer emulsion or admixture and sand. The polymer cement mortar mixture should be used up within 1 hour. In the construction process, if there is segregation, should be secondary mixing, if necessary, should be added to the right amount of polymer emulsion, no arbitrary addition of water. 2.2 plastering polymer cement mortar, its thickness is generally 5mm ~ 20mm (depending on the level of the base) , when plastering should pay attention to compaction, leveling. In the corner, should be wiped radius of 50mm above the rounded corner. The width of polymer cement mortar is 100mm ~ 300mm wider than the length and short edge of the roll, and the smoothness is ensured during the spreading process. 3, the details of the additional layer paste: in a large area of the roll before the roll should be placed on the three corners, water outlets, underground through the wall pipe and other vulnerable parts of the leakage of a roll or film, and before or after treatment with sealing materials to form a multi-channel structure, additional waterproof layer can be done according to the engineering conditions can be done first or later.
4. Large area of self-adhesive waterproof layer:
4.1 plane: remove the diaphragm on the lower surface of the self-adhesive waterproofing membrane and lay the waterproofing membrane on the polymer cement mortar. When the overlap method is adopted, the separation film on the upper surface of the lower layer coiled material and the separation film on the lower surface of the upper layer coiled material are removed, and then the overlap is tight, and the overlap width is not less than 60mm. When adopting the butt joint method, the upper and lower surfaces are sealed with the sealing material (self-adhesive coil or coating film) . 4.2 fa?ade: on the base of the pop-up coil placement control line, spread the prepared polymer cement mortar (the amount of preparation must be used within 1 hour) . Remove the membrane from one end of the coil, pull down the membrane evenly, and stick the part of the membrane to the polymer cement mortar. Side plastering, side laying coiled material side with a trowel gently smudging pressure, patting the surface of coiled material, exhaust, lift slurry, so that coiled material and cement mortar closely bound. When laying coiled material, pay attention to align with the datum line at any time, the speed should not be too fast. The vertical coiled material and the base, the coiled material and the coiled material all adopt the full stick method construction. 4.3 lap joint and seal of Coil: the lap joint of adjacent coil and the end of coil should be carefully treated, which can be sealed with matching sealing material or sealed with self-adhesive sealing strip, and then sealed with matching sealing material. 4.4 vertical roll-in: to prevent moisture loss at the vertical roll-in, the roll-in should be sealed temporarily (sealing material or thickened cement slurry can be used) . Can also be sealed with matching sealing materials, or with self-adhesive sealing strips for the cover seam, and then sealed with matching sealing materials to strengthen treatment.
5, waterproof layer acceptance: check all self-adhesive coiled material surface is torn, punctured, repair should be in the defect area than the actual size of the defect area around the 100 mm width of the additional layer, with pressure roller compaction, edge seams are sealed with special sealing materials. 6. Construction of protective layer and isolation layer: after the completion and acceptance of the rolled material, the construction waste and garbage should be transported to the designated garbage site, keep the site clean, and clean the surface of the waterproof layer, take protective measures to waterproof layer and carry out waterproof protective layer construction according to design requirements.
注意事項Points to note：
必須按相關規范設置保護層，表面采用礦物粒（片）料覆面的卷材時，可不另設保護層。水泥砂漿、塊體材料或細石混凝土做保護層時，保護層與防水層之間應設置隔離層。
1、不同規格的產品分別堆放、不應混雜。
2、卷材平放時碼放高夫不超過5層，立放時單層堆放。
3、運輸時防止傾斜和測壓，儲存期為一年。
4、鋪貼卷材嚴禁在雨天、雪天以及以上大風中施工。
5、施工溫度低于5度時應采用熱風焊槍加熱后粘接。
6、施工前對人員進行安全宣講，確保施工現場安全防護設施齊全、消防設施按規定放置。
The protective layer must be set according to the relevant specifications. When the surface is covered with rolled material with mineral grain (sheet) material, no additional protective layer can be set. When cement mortar, block material or fine stone concrete is used as protective layer, an isolation layer shall be set between the protective layer and the waterproof layer. 1, different specifications of products stacked separately, should not be mixed. When the coil is laid flat, lay down Gough no more than 5 layers, stand up when the stack of single layer. 3. Prevent tilting and pressure measurement during transportation. The storage period is one year. 4. It is strictly forbidden to lay and stick the coiled material in the rain, snow and above gale. 5, construction temperature below 5 degrees should be used hot air welding torch after heating bonding. 6, before the construction of personnel safety awareness, to ensure that the construction site safety protection facilities, fire facilities in accordance with the provisions placed.
保質期Expiration date：
原裝密封產品在干燥陰涼的環境下存放。在正常的儲存和運輸條件下，產品的保質期為一年。
The original sealed product is stored in a dry and cool environment. Under normal conditions of storage and transportation, the shelf life of the product is one years.
全國免費服務熱線：400-843-6198 www.xzlqcc.com
?