固浪聚合物JS防水涂料

Solid wave polymer JS waterproof coating

固浪聚合物JS防水涂料固浪聚合物JS防水涂料是一種以聚丙烯酸酯乳液、乙烯-醋酸乙烯酯共聚乳液菩聚合物乳液與各種添加劑組成的鶴機液料。和水混、石英動、輕重質碳酸鈣等無機填料及各種添加劑所組成的羌機粉料通過合理配比、復合制成的。

Gulang polymer JS waterproofing coating gulang polymer JS waterproofing coating is a kind of liquid material composed of polyacrylate emuls

ion, ethylene-vinyl acetate copolymer emulsion and various additives. Mixed with water, quartz, light and heavy calcium carbonate and other inorganic fillers and additives composed of Qiang machine powder by a reasonable ratio, made of composite.

產品特點Product characteristics：

1∶無毒、無害、無污染、易施工，是新一代環保型防水材料。

2:可在潮濕的基面上施工，具有良好環境適應性。

3∶單組份、冷施工、可以用刷、滾、噴、刮等方式進行施工、開蓋直涂。

4:具有良好耐候性好、耐老化、延伸性、彈性、粘結性和成模性。

5︰防水層為封閉體系，整體防水效果佳，特別適用于異形結構基層的施工。

1: non-toxic, harmless, non-polluting, easy to construction, is a new generation of environmental protection waterproof materials.

2: can be constructed on the wet base surface, with good environmental adaptability.

3: Single Component, cold construction, you can use brush, roll, spray, scrape and other means of construction, open straight coating.

4: good weather resistance, good aging resistance, extensibility, elasticity, adhesion and molding.

5. The waterproofing layer is a closed system with good overall waterproofing effect, which is especially suitable for the construction of special-shaped structure base course.

使用范圍Scope of use：

本產品廣泛應用于新舊屋面、內外墻、陽臺、水池、隧道、地下通道等防水防潮工程。尤其適用于工業及民用建筑的屋面防水、墻面、槽罐等防水。

This product is widely used in new and old roofing, inside and outside walls, balconies, pools, tunnels, underground passages and other waterproof and moisture-proof projects. Especially suitable for industrial and civil building roofing waterproof, wall, tank and other waterproofing.

施工工藝Construction Technology：

1、先將水泥倒入容器中，再將乳液慢慢加入，同時充分?jǐn)嚢?-5分鐘至形成無生粉團和顆粒的均勻漿料即可使用;(最好使用攪拌器)
2、用毛刷或滾刷直接涂刷在基面上，力度使用均勻，不可漏刷;一般需涂刷2遍(根據使用要求而定)，每次涂刷厚度不超過1mm;前一次略微干固后再進行后一次涂刷(剛好不粘手，一般間隔1-2小時)，前后兩次垂直十字交叉涂刷,涂刷總厚度一般為1-2mm;如果涂層已經固化涂刷另一層時先用清水濕潤。

3、施工24小時后建議用濕布覆蓋涂層或噴霧灑水對涂層進行養護。施工后完全干固前請采取禁止踩踏、雨水、暴曬、尖銳損傷等保護。

4、如有更高防水要求，進行多遍涂刷或添加玻璃網格布，效果更佳。

1. First pour the cement into the container, then slowly add the emulsion, while fully stirring for 3-5 minutes to form a non-raw powder and particles of uniform slurry can be used; (preferably using agitator)

2, with a brush or roller brush directly brush on the base surface, the force to use uniform, not brush; generally need to brush 2 times (according to the use requirements) , each brush thickness not more than 1mm; After the previous slightly dry and then after a brush (just non-stick hand, generally 1-2 hours interval) , before and after two vertical cross brush, brush the total thickness of 1-2 mm; If the coating has been cured when brushing another layer of water first wet.

3. After 24 hours of construction, it is recommended to cover the coating with wet cloth or spray water to maintain the coating. After construction, please take no trampling, rain, sun exposure, sharp injury and other protection before completely dry.

4, if there is a higher waterproof requirements, repeated brushing or add glass mesh cloth, the effect is better.

參考用量Reference dosage： 

防水涂膜厚度1.5mm,用量約為1.5-2.0kg/m(實際用量視基面的實際情況以及需求的防水層厚度而定)。

The thickness of waterproof film is 1.5 mm, the dosage is about 1.5-2.0 kg/m (the actual dosage depends on the actual condition of the base surface and the required waterproof layer thickness) .

注意事項Points to note：

1、施工溫度應在5℃至35℃，避免高溫和室外陰雨天氣使用。

2、粉料和液料拌合后會逐漸硬化故必須3小時內用完，氣溫高于20℃還要縮短。

3、配料時，應將粉料往液料內緩緩加入，邊加粉料邊攪拌，充分?jǐn)嚢璩刹缓w粒，分散均勻的膠漿為止。靜置5-10分鐘再施工，切勿另外加水。

4、施主完畢后注意通風，使材料更好的固化成膜。切勿踩踏以免破壞水涂膜，至少48小時后進行閉水試驗(視溫度而定)

1. Construction temperature should be 5 ° C to 35 ° C, avoid high temperature and outdoor overcast rain weather use.

2. The powder and liquid material will gradually harden after mixing, so it must be used up in 3 hours, and the air temperature above 20 °C will be shortened.

3, batching, should be the powder into the liquid material slowly, while adding powder while stirring, fully stirring into no particles, evenly dispersed until the mortar. Let stand for 5-10 minutes before construction. Do not add water.

4, donors after the attention of ventilation, so that better curing materials into film. Do not step on the film to avoid damaging the water, at least 48 hours after the water test (depending on the temperature)

保質期Expiration date：

原裝密封產品在干燥陰涼的環境下存放。在正常的儲存和運輸條件下，產品的保質期為一年。

The original sealed product is stored in a dry and cool environment. Under normal conditions of storage and transportation, the shelf life of the product is one years.

全國免費服務熱線：400-843-6198      www.xzlqcc.com

?